Блог

Core concept: Why are pure electric bending machines more user-friendly for beginners?

1. Simplified operation: Fully electric control eliminates the need for complex hydraulic calibration, resulting in less noise and heat generation.

2. Precision self-protection: The servo system can precisely control the position and speed of the slider, with extremely high repeatability accuracy. Once adjusted, there is no need to worry about batch production.

3. Safety and Intelligence: Usually equipped with a more user-friendly graphical interface, anti-collision hand function, and misoperation prompts, etc.

4. Maintenance-free: No hydraulic oil is required, reducing maintenance steps and contamination risks.

The four-step method for beginners to easily get started

Step 1: Preparations before commencement - Safety and understanding

Read the manual: Spend 30 minutes browsing through the equipment operation manual to understand the emergency stop, various buttons and interface areas.

Wear protective gear: Be sure to wear protective gloves (to prevent cuts), goggles (to prevent iron filings from splashing), and safety shoes.

Get to know your workpiece

Material: What is it? For example: cold-rolled steel plates, stainless steel, aluminum

Thickness: How much? (e.g. 1.5mm

Bending Angle: How many degrees should it be bent to? (e.g. 90°

Size: What is the length of the bent edge?

Step 2: Machine Setup - Utilize the intelligent system

This is the most crucial step. The control system of the pure electric bending machine is your "strongest assistant".

Input parameters: On the control touch screen, select "New Program" or "Single Processing", and input:

Material type

Material thickness

The V-groove opening of the lower die (generally, 6 to 8 times the thickness of the plate is selected; for example, a 12mm V-groove is chosen for a 1.5mm plate.) The system has recommended values.

Target bending Angle

Bending length

Let the machine calculate automatically: Press the "Program" or "Calculate" key, and the machine will automatically calculate:

Lower die position

Bottom dead center of the upper mold (slider depth)

Required pressure

Rear stopper position

Install the mold

Power-off operation! Make sure the machine has completely stopped.

According to the system suggestions, select the appropriate upper die (sharp knife, curved knife, etc.) and lower die (V-groove).

Use a tool (an Allen wrench) to install it firmly, but do not over-tighten.

Step 3: Trial folding and fine-tuning - Patiently verify

To perform the "trial folding" : Place a piece of scrap material of the same material and thickness as the workpiece, and press the foot switch or click "Single cycle" to conduct the trial folding.

Measure the Angle: Use an Angle gauge to measure the Angle of the workpiece to be folded.

If the Angle is too large (such as 95°) : It indicates that the bending is insufficient. Add the "bending depth" or "correction value" (for example, +0.1mm) on the control screen.

The Angle is too small (such as 85°) : It indicates that the bending is too deep. Reduce the "bending depth" (for example, -0.1mm) on the control panel.

Adjust the rear stopper: If the bending position is incorrect, adjust the front and back positions of the rear stopper.

Repeated fine-tuning: Usually, after 2 to 3 attempts of bending and fine-tuning, a perfect Angle can be achieved. The advantage of the pure electric bending machine lies in that the adjusted parameters will be automatically saved and can be directly called up when bending the same product next time.

Step 4: Formal bending and mass production

Confirmed to be correct: The Angle and size of the test folded piece are completely qualified.

Batch bending

Place the workpiece close to the rear stopper.

Place both hands on both sides of the workpiece. Do not put them under the mold.

Step on the foot switch to complete the bending.

Repeat the operation and enjoy the stable repeat accuracy of the machine.

First article inspection: Regularly spot-check the first article during batch production to ensure there are no deviations.

Have questions about the parameters of this model?

Click here to consult our chief technical engineer.

Tel: +86 -18855551088

Email: Info@Accurl.com

Whatsapp/Mobile: +86 -18855551088